Hand Tools

Drill bit sizes are written as irreducible fractions . So, instead of 78/64 inch, or 1 14/64 inch, the size is noted as 1 7/32 inch. Below is a cart providing the decimal-fraction equivalents that are most relevant to fractional-inch drill bit sizes (that is, 0 to 1 by 64ths). (Decimal places for . If you know the size of the screw, you can locate the size of the drill bit by looking at the opposite end from the sharp point of the bit. It's likely engraved there. Standard metric sizes are defined in ISO 2936:2014 "Assembly tools for screws and nuts —Hexagon socket screw keys", also known as DIN 911. The full set of defined sizes are: 0.7 mm, 0.9 mm, 1.3 mm. 1.5 to 5 mm in 0.5 mm increments. They're great for being able to be quickly swapped out if you an adapter, and even without an adapter that hex shank is a lot easier for your drill chuck to grab onto when using very small bits like 1/16” & smaller. You'll see a list of numbers from to 10 or 20. These are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener that can be driven. To adjust your clutch, align the arrow to a lower setting and start driving a screw. Take a loose screw and compare it to the size of the bit you need to use, using the screw's core rather than its flute. A bit that is very slightly smaller than the screw will ensure a proper fit. Choosing a bit that is too small means that the screw will get stuck so take care to choose carefully. In hex, four digits of a binary number can be represented by a single hex digit. Dividing a binary number into 4-bit sets means that each set can have a possible value of between 0000 and 1111, allowing 16 number combinations from 0 to 15. With the base value as 16, the maximum value of a digit is 15.

The C-Mart M0016 straight (copper) water gun features a one-piece brass nozzle with snap-on adapter and an additional brass hose connector. The C-Mart M0016 Straight Water Spray Gun features all brass construction for rust resistance and durability.

Y-Type Socket Wrench

Impact Socket Extension Bar

Spirit Level

Hans Spark Plug Socket

Hans Spark Plug Socket

PVC Pipe Cutter

Magnetic Spark Plug 1/2" DR. X 13/16" - Inches Size

Magnetic Spark Plug 1/2" DR. X 14MM - Metric Size

Magnetic Spark Plug 1/2"DR X 5/8" - Inches Size

INGCO Claw Hammer HCH80808

PLIERS LOCKING CURVED JAW 250MM/10"

CREW PLIERS CR-V 160MM-ME200029

INGCO Fiberglass Axe 600g HAX0206008

3/8" DR. 9PCS. Hex Bit Socket Set

INGCO Combination Pliers 100cm HCP08181

PLIERS SET PRECISON 2-PCS-ME545301

Shinsetsu SWB6414P Wheelbarrow 160Kg Move materials around their property.

RIGHT CUTTING OFFSET SNIPS - 48-22-3079 shopping for tin snips, and specifically for aviation snips, you'll notice several types: straight-cut, right-cut and left-cut snips, often marked with yellow, green and red, respectively. Each is suited to specific cutting tasks. The forged steel jaws of these left-cutting or right -cutting snips are set at a 90- degree angle to allow easy gripping when cutting sheet metal in tight spaces or overhead. The operator can follow tight circular or square pattern left or right cuts with either a pushing or pulling motion.Left cut snips are for making to the left and straight cuts. Right cut snips are for making straight and cuts to the right. Straight cut snips (not shown) are for making straight cuts and shallow cuts to the right or left. Right hand tin snips are suitable for cutting straight lines and cutting off in an anti-clockwise direction. Best suited for right handed use. hand tin snips are suitable for cutting off in a clockwise direction and for cutting straight lines. Best suited for left handed use. Types of Tin Sni They are also useful for making long cuts through sheet metal, should you need to. However, you're going to make a long cut through sheet metal, especially a straight one, a pair of snips with offset handles is the way to go. Each color signifies a different direction that the snips are made to cut. Red snips cut left. Yellow snips cut straight or left and right. Green snips cut right. HVAC and sheet metal pros agree: When making long, straight cuts in thinner-gauge sheet metal, tinner snips are the way to go. They're a simple, economical, and durable cutting solution for many sheet metal and HVAC applicatioN.

1" DR. Dual Opening Budd. Heavy Duty

1" DR. Dual Opening Budd. Heavy Duty

1" DR. Dual Opening Budd. Heavy Duty

1" DR. Dual Opening Budd. Heavy Duty

INGCO Combination Pliers 6"/160mm HCP08168

EDG012-1 Deli Cordless Leaf Blower 20V

4 Way Cross Wrench 16"

INGCO Combination Pliers 7"/180mm HCP08188

2 Way Truck Tire Wrench

2 Way Truck Tire Wrench