You have no items in your shopping cart.

Pressure Tank

Filters
per page
Aluminum Flexible Hose [50cm] with Elbow 1" x 1"
₱800.00
Automatic Pump Control
₱1,700.00
Brass 5 Way Connector
₱350.00
Butyl Bladder Pressure Tank
₱5,700.00
Butyl Bladder Pressure Tank
₱6,380.00
Float Switch
₱600.00
Pressure Manometer Gauge
₱180.00
₱6,200.00
PRESSURE GAUGE (0-6 BAR) 50MM AXIAL-LOPGS5OR
₱312.00
A Jet Pump is a type of a impeller-diffuser pump that is used to draw water from wells into residences. It can be used for both shallow (25 feet of less) and deep wells (up to about 200 feet.)
₱14,125.00
PRO CB BETON SOFT LASER Discover Norton Core Bits especially designed for drilling. Reinforced concrete, cured concrete, kerb stones, concrete, pipes, engineering bricks, facing bricks, refractory bricks, flagstones and paving stones, block paving, washed gravel concrete slabs, natural stone , flint, sandstone, limestone. Useful length: 450mm Connection: 1-1/4" UNC female thread Applications: Concrete, Reinforced concrete and hard building materials 10mm brazed segmenteds for wet and dry drilling. Special soft bound for use in harder materials or for high speed drillings. We are able to manufacture to your specification diamond core drill bits from 10 - 1000mm Diameter ½″ BSP and 1 ¼” UNC thread, in a variety of lengths with segments available for reinforced concrete, asphalt and brickwork; we also offer a brilliant re-tipping service. Core drill bits are specifically designed for cutting precise circular holes in most construction materials like brick, stone, concrete and masonry. Made from steel, the diamond core drill bit comes in many lengths and has various sized teeth depending on the material and cutting requirement. A core bit (Fig. 1, Fig. 2) is a drilling tool with a hole through the center that removes sediment rock and allows the core pedestal to pass through the bit and into the core barrel. A 220 V core drill of 2000 W will do well for coring less than 500 mm, however, it is better to turn to a core drill at 380 V of at least 4000 W for deep core drilling. You can use a drilling bit to make a hole or you can use a core bit to remove a core of glass and leave a hole. The difference is that a drill bit will create the hole size that it advertises, but the core bit will create a circle of glass in the size that it advertizes.
₱17,500.00 ₱14,000.00
SAFETY PRESSURE REALEAS VALVE-KJ40QSV
₱18.00
Note: Pre-charge pressure must be less than 2PSI below cut-in pressure. Factory Precharge: 30 P.S.I. / 2 bar Maximum Pressure: 150 P.S.I. / 10 bar Maximum Temperature: 90 Celsius Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. An advantage of bladder pressure tanks is that they typically last longer than diaphragm pressure tanks, since they don't have a diaphragm that can fail. The diaphragm is a muscle that helps you breathe. It sits under your lungs and separates your chest cavity from your abdomen. Many conditions, injuries and diseases can affect how the diaphragm works, causing symptoms such as trouble breathing and chest pain.
₱13,438.00 ₱10,750.00
Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. An advantage of bladder pressure tanks is that they typically last longer than diaphragm pressure tanks, since they don't have a diaphragm that can fail. Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations . It decreases the running time of the booster pumps, thereby making the system more energy effective.
₱25,625.00 ₱20,500.00
Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. An advantage of bladder pressure tanks is that they typically last longer than diaphragm pressure tanks, since they don't have a diaphragm that can fail. An important thing to remember, the higher the operating pressure – the larger the tank must be. Pressure and tank size have a direct correlation – as one increases, so does the other. The disadvantage may be the need to check the overpressure in the vessel regularly, due to the possibility of air leakage. In the event of a leak, the air in the vessel would be reduced , which would switch the pump more often and more water would flow into the bladder. This would create a risk of the bladder tearing.
₱30,000.00 ₱24,000.00
Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. Diaphragm pressure tanks are the most efficient type of pressure tank and require the least amount of maintenance due to the use of a rubber lining inside that separates the air and the water. This rubber lining acts as the bladder would, but its connection is permanent to the tank. Therefore, it is not replaceable. If this happens, there is little air left in the tank to become compressed, so the pump runs nearly every time water is used. In addition, too much air in the tank is a problem because it reduces the space for water storage. Extra air must be released or the tank will become air-bound.
₱37,500.00 ₱30,000.00
Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. A well pressure tank can last from five to 15 years, as long as yours is well maintained. If this happens, there is little air left in the tank to become compressed, so the pump runs nearly every time water is used. In addition, too much air in the tank is a problem because it reduces the space for water storage. Extra air must be released or the tank will become air-bound. As stated before, there are three types of tanks: Air-Over-Water, Diaphragm, and Bladder. Typically a double diaphragm pump will be able to run continuously at between 40 and 60 cycles per minute and intermittently
₱45,000.00 ₱36,000.00
Diaphragm tanks are commonly used on the discharge manifold to provide water storage for the system in very low flow situations. It decreases the running time of the booster pumps, thereby making the system more energy effective. An advantage of bladder pressure tanks is that they typically last longer than diaphragm pressure tanks, since they don't have a diaphragm that can fail. Diaphragm pressure tanks are the most efficient type of pressure tank and require the least amount of maintenance due to the use of a rubber lining inside that separates the air and the water. This rubber lining acts as the bladder would, but its connection is permanent to the tank. Therefore, it is not replaceable. If this happens, there is little air l eft in the tank to become compressed, so the pump runs nearly every time water is used. In addition, too much air in the tank is a problem because it reduces the space for water storage. Extra air must be released or the tank will become air-bound.
₱70,000.00 ₱56,000.00
TANK-KJ40QT
₱0.00
TANK-KJ50WT
₱625.00
TANK-KJGNS15T
₱188.00
Close